ĥ maintenance en-18 5.3 engine oil _ check the engine oil at the start of each day before starting the engine. If proper adjustments cannot be made contact an authorized cushman dealer. Adjustment and maintenance should always be performed by a qualified technician. Maintenance 5 en-17 5 maintenance 5.1 general _ 1. Notice all torque values included in these charts are approximate and are for reference only. To remove belt rotate tensioner towards radiator.Ĥ adjustments en-16 4.10 torque specification_ jacobsen uses grade 5 (inch) or grade 8.8 (metric) bolts as standard, unless otherwise noted. Belt is dynamically adjusted with a spring loaded tensioner to 12 ft-lbs. Push at midpoint be.Īdjustments 4 en-15 4.8 gas hydraulic pump belt _ inspect new belt after first 24-48 hours of operation. Adjust alternator pulley so belt deflects 1/4 to 1/2 in. To open the front cowl locate the release lever at the upper left corner of front clip near the le.Ĥ adjustments en-14 4.5 diesel alternator belt _ inspect and adjust new belt after first 24-48 hours of operation. Replace, do not adjust, wo.Īdjustments 4 en-13 4.3 front cowl access_ the front cowl opens to gain access to two access panels, fuse panel, horn, and master cylinder reservoir.
If proper adjustment cannot be made, contact an authorized cushman dealer. Adjustments and maintenance should always be performed by a qualified technician.
Quick disconnect flatb.ģ specifications en-10 declaration of conformity prohlÁenÍ o shod overensstemmelseserklÆring conformiteitsverklaring vastavusdeklaratsioon vaatimustenmukaisuusvakuutus declaration de conformite konformitÄtserklÄrung megfelelsÉgi nyilatkozat dichiarazione di conformitÀ atbilstbas deklar!Cija atitikt. Specifications 3 en-9 3.7 accessories & support literature _ contact your area jacobsen dealer for a complete listing of accessories and attachments. 24 x 13 -12 titan ultra trac tire pressure: front. ģ specifications en-8 3.4 vehicle _ t ires: front.
CUSHMAN TRUCKSTER PARTS CATALOG MANUAL
Turf truckster, liquid cooled diesel engine, 4 speed manual transmission, 11.16:1 2 speed differential, mechanical pto, and four post rops. Specifications 3 en-7 3 specifications 3.1 product identification _ 84063.
CUSHMAN TRUCKSTER PARTS CATALOG SERIAL
Warning - indicates a pote.Ģ vehicle identification numbers en-6 2 vehicle identification numbers 2.1 vehicle identification number _ the vehicle identification number (vin), consisting of the model number, date code, and serial number, is printed on the nameplate/identification decal a. Danger - indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Safety 1 en-5 1.2 important safety notes _ this safety alert symbol is used to alert you to potential hazards. It is your responsibility to read this man. Never allow minors to operate any equipment. Safety is dependent upon the awareness, concern and prudence of those who operate or service the equipment. ġ safety en-4 1 safety 1.1 operating safety _ 1. 5 2 vehicle identification numbers 2.1 vehicle identification number. This manual should be store.Įn-3 table of contents 1 safety 1.1 operating safety.
“all rights reserved, including the right to reproduce this material or portions thereof in any form.” this manual contains adjustment, maintenance, troubleshooting instructions and parts list for your new jacobsen ® machine.
© copyright 2011, jacobsen, a textron company. Les opérateurs et le personnel d’entretien doivent être formés et conscients des dang. ™ avertissement risque de blessures graves en cas d’utilisation incorrecte de la machine. Parts & maintenance manual manuel de maintenance & nomenclature des pièces de rechange by jacobsen when performance matters. If incorrectly used, this machine can cause severe injury. Those who useĪnd maintain this machine should be trained in its proper use, warned of itsĭangers and should read the entire manual before attempting to set up,Īvec structure de protection anti-retournement à 4 montants Ils doivent lire avec attention le manuel avantĭ’essayer de monter, d’utiliser, de régler ou maintenir la machine. Les opérateurs et le personnel d’entretien doivent être formés et conscientsĭes dangers encourus. Risque de blessures graves en cas d’utilisation incorrecte de la machine.